IPM1 Configuration Sheet: Your Wiring Roadmap
Have the legacy kit? See our Configuration Sheet guide for the legacy system instead.
Your configuration sheet is your roadmap to wiring your Infinitybox system. This guide covers the sheet that comes with the next generation IPM1 kit. In most cases it’s stapled to the back of the manual that shipped with your kit.
Where to find your configuration sheet
Go to www.infinitybox.com, click Resources in the top bar, and look under Documentation on the left for System Configurations. For the IPM1 kit there are two versions:
- Front engine: the engine and starter are controlled on the front POWERCELL. This is the right one for most customers’ cars.
- Rear engine: for rear and mid-engine builds.
This guide walks through the front engine sheet.
How the sheet is organized
- Front POWERCELL: outputs for the front of the car
- Rear POWERCELL: outputs for the rear of the car
- MASTERCELL: a dedicated page for the MASTERCELL’s own outputs, which is new with the IPM1 kit
- inMOTION: functions and outputs for the inMOTION NGX control
Reading the columns
Each row is one function, which is a load the system controls, such as turn signals, four-ways, ignition, starter, lights, and horns. Going across:
- Function: what the system is controlling.
- POWERCELL address: the IPM1 kit has two POWERCELLs. The front is address 1 and the rear is address 2. Some functions, like four-ways, use both.
- POWERCELL output: the output number, 1 through 10, on that POWERCELL.
- POWERCELL connector: whether the A or B connector controls that function. The manual defines both.
- Personality: how an output turns on or off when the MASTERCELL tells it to. Turn signals have a turn signal personality, so they flash. The most basic personality is track: switch on, output on; switch off, output off.
- POWERCELL wire color
- Switch input: the input number. Use it for troubleshooting along with the Insight screen on the MASTERCELL.
- MASTERCELL connector: the A connector is above the screen and the B connector is below it.
- MASTERCELL wire color
Example: the headlights
On the front POWERCELL sheet, the headlights are output 5 on the B connector, on the white wire. On the MASTERCELL, the input is on the A connector, on the white wire with the green tracer.
Yellow blocks and white blocks
The yellow blocks can’t be changed. Everything in white can be changed and configured with inCODE NGX. See our inCODE NGX video series for how.
“Open” outputs
Any function marked open is an auxiliary output. Use it for whatever you need, such as extra lights, fans, or pumps.
Functions with more than one input
Some functions can be triggered two ways. The cooling fan, for example, has a ground-switched input and a 12-volt switched input. You can ground-switch the fan trigger with something like a thermostatic switch, or high-side switch it from an EFI or other fuel injection system. The sheet gives wire colors for both.
Rear POWERCELL outputs
The rear POWERCELL page lists the outputs for the back of the car, including additional open outputs.
MASTERCELL outputs
These outputs drive the indicators on your dash:
- Left and right turn signal indicators
- High beam indicator
- Gauge illumination
- Ignition indicator, on when the ignition is on
- Security indicator, on when security is enabled from inLINK
- Two open low-current outputs for other dash functions
Questions?
Your configuration sheet is your roadmap for wiring the car, and we’re happy to walk you through it. Call us at 847-232-1991 or contact us.

Copyright 2026, Infinitybox LLC. All Rights Reserved.
Copyright Infinitybox, LLC 2021. All Rights Reserved.
Copyright Infinitybox, LLC 2021. All Rights Reserved.
Copyright Infinitybox, LLC 2021. All Rights Reserved.
Copyright Infinitybox, LLC 2021. All Rights Reserved.
Copyright 2026, Infinitybox LLC. All Rights Reserved.
Copyright 2026 Infinitybox, LLC. All Rights Reserved.
Leave a Reply
Want to join the discussion?Feel free to contribute!